Lantronix XPress-DR-IAP User's Guide Page 96
- Page / 149
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Monitor Mode
Table 21 - Monitor Mode Commands
Command Name Function
DL Download Download firmware to the Device Server via the
serial port in hex format
SF x.x.x.x Send Firmware Send firmware to Device Server with IP address
x.x.x.x
Version Query software header record (16 bytes) of
Device Server with IP address x.x.x.x
GC x.x.x.x Get configuration of Device Server with IP
address x.x.x.x as hex records (120 bytes)
SC x.x.x.x Send Configuration
Command
VS x.x.x.x
Get Configuration
Set configuration of Device Server with IP address
x.x.x.x from hex records
PI x.x.x.x Ping Ping Device Server with IP address x.x.x.x to
check device status
AT ARP Table Show the Device Server’s ARP table entries
TT TCP Connection
Table
Shows all incoming and outgoing TCP
connections
NC Network Connection Shows the Device Server’s IP configuration
RS Reset Resets the Device Server’s power
SI
xxx.xxx.xxx.xxx:
yyy.yyy.yyy.yyy
Send/Set IP
Address
Remotely assign an IP address to a Device
Server, where xxx.xxx.xxx.xxx is the IP address,
and yyyy.yyy.yyyy.yyy is the two-part identification
number at the bottom of the label, converted to
decimal, and written twice.
QU Quit Exit diagnostics mode
G0, G1, ....,Ge,
Gf
Get configuration
from memory page
Gets a memory page of configuration information
from the device.
S0, S1,...,Se, Sf Set configuration to
memory page
Sets a memory page of configuration information
on the device.
Responses to some of the commands are given in Intel Hex format (see The Intel Hex Format
on page 8-5).
Note: You may be required to enter QU twice to exit monitor mode.
Entering any of the commands listed above will generate one of the following command
response codes:
Table 22 -Command Response Codes
Response Meaning
0> OK; no error
1> No answer from remote device
2> Cannot reach remote device or no answer
8> Wrong parameter(s)
9> Invalid command
7-2 DSTni-XPress DR User Guide
- DSTni-XPress DR 1
- User Guide 1
- Copyright and Trademark 3
- Disclaimer and Revisions 4
- Declaration of Conformity 5
- Warranty 6
- Sales Offices 7
- Contents 10
- List of Figures 12
- List of Tables 13
- 1.1 DSTni-XPress DR 15
- Introduction 16
- PLC's XPress DR-IAP 17
- 1.4 Serial Interface 19
- 1.5 RJ-45 Serial Connector 20
- 1.7 RJ-45 Ethernet Interface 22
- 1.9 Front Panel Description 25
- 1.10 LEDs 27
- 1.11 Dimensions 28
- 1.13 Power Requirements 29
- 1.14 Reset Switch 29
- 1.15 RS-232/RS-485 Switch 30
- Table 7 - Technical Specs 31
- Getting Started 33
- 2.1.3 Port Number 34
- 2.3.1 DHCP 37
- 2.3.2 AutoIP 37
- 2.4 DeviceInstaller 38
- 2.4.3 Test the IP Address 40
- 2.5 ARP and Telnet 44
- 2.6 Serial Port Login 45
- Configure 47
- 3.2 Using DeviceInstaller 48
- 3.3 Web Manager Page 50
- 3.3.1 Unit Configuration 51
- 3.3.2 Server Properties 52
- 3.3.3 Port Properties 53
- 3.3.4 Update Settings 55
- 3.3.5 Technical Support 55
- 3.4.2 Using the Serial Port 58
- 3.5.1 IP Address 58
- 3.5.5 DHCP Naming 60
- 3.6.1 Baudrate 61
- 3.6.2 I/F (Interface) Mode 61
- 3.6.3 Flow 62
- 3.6.4 Port Number 63
- 3.6.5 Connect Mode 64
- 3.6.6 Remote IP Address 67
- 3.6.7 Remote Port 67
- 3.6.8 DisConnMode 67
- 3.6.10 Pack Control 69
- 3.6.12 Send Characters 70
- 3.6.13 Telnet Terminal Type 70
- 3.7 Expert Settings 71
- 3.8 Security Settings 71
- 3.9 Factory Defaults 73
- 3.11 Get Configuration 73
- 3.12 Set Configuration 74
- 4.1 Protocol Firmware 75
- 4.2.1 Via DeviceInstaller 76
- Firmware 77
- 4.2.2 Via TFTP 79
- 4.2.3 Via Another Unit 79
- 4.2.4 Via the Serial Port 80
- 5.1 Overview 81
- Comm Port Redirector 82
- 5.3 Using Redirector 83
- 5.3.1 Port Setup 84
- 5.3.2 Comm App Setup 84
- 5.3.5 Port Settings 86
- 5.3.6 Listen Mode 86
- 5.3.7 Silent Mode 87
- 5.3.8 TCP Keepalive 87
- 6.1 Technical Support 89
- Troubleshooting 90
- 7.1 Monitor Mode 95
- 0> OK; no error 96
- 8> Wrong parameter(s) 96
- 9> Invalid command 96
- 8.1 UDP Datagrams 97
- 8.2.2 Sending a Setup Record 100
- 8.2.3 The Intel Hex Format 101
- 0300300002337A1E 102
- 8.3 Setup Records 103
- 8.3.1 Channel Parameters 104
- 8.3.2 Interface Mode 105
- 8.3.3 Baud Rate 106
- 8.3.4 Flow Control 106
- 8.3.5 Connect Mode 107
- 8.3.6 Disconnect Mode 108
- 8.3.8 Pack Control 109
- 8.4 IP Addresses 110
- 8.4.3 Host Portion 111
- 8.4.4 Network Address 111
- 8.4.5 Broadcast Address 111
- 8.4.7 Network RFCs 112
- 9.1 Connect Mode Options 114
- Binary to Hex 115
- 9.2 Disconnect Mode Options 117
- 9.4 Interface Mode Options 126
- 9.5 Pack Control Options 127
- 10.1 Class A Network 129
- 10.2 Class B Network 129
- 10.3 Class C Network 129
- 10.4 Network Address 130
- 10.5 Broadcast Address 130
- 10.6 IP Netmask 130
- 10.8 Network RFCs 131
Related products and manuals for Serial servers Lantronix XPress-DR-IAP
Serial servers Lantronix MSS4 User's Guide
(81 pages)
(81 pages)
Serial servers Lantronix EDS4100 User's Guide
(163 pages)
(163 pages)
© 2020, manymanuals.com. All rights reserved. | 1.560 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals